SPA CARE GUIDE
ALWAYS HAVE THE CIRCULATION SYSTEM
RUNNING BEFORE ADDING ANY CHEMICALS.
ALWAYS DISSOLVE CHEMICALS IN A BUCKET OF WATER BEFORE
ADDING TO SPA.
-----------------------------SPA START-UP
-------------------------------
Step 1.
As spa is being filled through filter housing, add 3 oz. PROTECT
PLUS to prevent any mineral staining and scale formation and to protect spa equipment. If
your source water is high in iron you may need to double or even triple initial dose of
PROTECT PLUS. Always fill your spa with "hard" water.
Step 2. Circulate Water for 2 hours to remove iron and minerals.
Step 3. Test water for alkalinity and pH levels using a dip and read test strip. Follow
instructions on test strip bottle label.
a. If pH is lower than 7.2, add pH-UP
in 1 Tbls per dose amounts.
b. If pH is higher than 7.8, add
pH-DOWN in 1 Tbls per dose amounts.
c. If total alkalinity is above 120
PPM, add pH-DOWN in 1 Tbls per dose amounts.
d. If total alkalinity is below
80 PPM, add ALKALINITY-UP in 1 Tbls per dose amounts.
You may need to add multiple doses to adjust pH and
Alkalinity. If that is the case always circulate the water for at least 2 hours between
tests. This may take several days to balance on the initial fill-up. Keep a record of how
much pH and Alkalinity adjusters you use. On subsequent fill-ups you can speed the process
by increasing the doses depending on the amount you used on the initial fill-up.
Step 4. Fill automatic dispenser or add 3 BROMINE TABLETS to the strainer basket.
Step 5. Add 1 packet of
BROMA-START
----------------------------- ROUTINE MAINTENANCE----------------------
Step 1.
Test water using dip and read test strips at least 3 times per
week. If needed, balance pH and Alkalinity. Check for Bromine residual of 3-5 PPM and add
BROMINE TABLETS to the strainer basket or automatic dispenser as needed. Follow the
instructions on the test strip bottle.
Step 2. Add 1 oz. of PROTECT PLUS
weekly to protect spa equipment from stains, scale and corrosion.
Step 3. Shock treat water with 4 - 5 oz. of ACTIVATE weekly to oxidize contaminants from
your spa.
Also 1 oz after heavy use is recommended.
Step 4. If bromine tests
on low side before using spa add 1 tsp granular chlorine after using spa.
Step 5. To digest oils, lotions and other organic material in the water, remove scum
lines, and to protect filters from oily build-up and clogging add 1/2 oz. of NATURAL CLEAR
per week during periods of heavy use.
---------------OCCASIONALLY----------------------------------TIPS----------
* Use small amount of FOAM OUT to reduce foaming and
sudsing.
* Always fill through the filter housing.
* Clean waterline and any above water surfaces with a
damp
sponge.
* Shower before use for cleaner water.
* Clean filter with FILTER FRESH and air dry at least
every 4
months.
* Turn power off when filling or draining spa.
* At least once per month rinse filter in hot, fresh
water and air
dry.
* Ideal spa water temperature is 95°-104°.
* Clean your spa cover with COVER CARE and protect the
top
with
* Always store chemicals dry and above 32°.
CONDITIONING CREAM monthly if outdoors, annually if
indoors.
* For safety always keep spa cover locked.
* Use 1-2 oz. of SPA CLARIFIER if cloudy or
"dull" water
develops.
* Always fill spa with hard water.
* Try IN-SPA FRAGRANCE for greater enjoyment of your
spa.
* Always run spa jets when adding chemicals.
* Change spa water at least every three months or sooner
if
chemical
* Avoid soap residuals on your body and
use
increases.
clothing during spa use.
CALL HÄNK'S SPA CARE HOT LINE IF YOU HAVE ANY
QUESTIONS. 320-255-1244
